{"id":2633,"date":"2025-04-09T11:08:29","date_gmt":"2025-04-09T11:08:29","guid":{"rendered":"https:\/\/www.woojin.help\/?p=2633"},"modified":"2025-07-16T08:19:02","modified_gmt":"2025-07-16T08:19:02","slug":"plaimmx-weight-control-te-500-6","status":"publish","type":"post","link":"https:\/\/www.woojin.help\/ko\/plaimmx-weight-control-te-500-6\/","title":{"rendered":"PLAIMMX Weight Control (TE.500.6)"},"content":{"rendered":"
<\/div>\n

Page Overview<\/strong><\/h3>\n\n\n\n
\"\"<\/figure>\n\n\n\n

<\/p>\n\n\n\n

Contents<\/h3>\n\n\n\n

\u2705 Enable of the function<\/strong><\/h4>\n\n\n\n
\"\"<\/figure>\n\n\n\n

<\/p>\n\n\n\n

Status of the function<\/strong><\/h4>\n\n\n\n
\"\"<\/figure>\n\n\n\n

This status message shows the current state<\/strong> of the weight control function, helping the operator understand whether the system is ready, active, or requires action.<\/p>\n\n\n\n

Status Messages:<\/strong><\/p>\n\n\n\n

    \n
  • Disabled<\/strong>
    The weight control function is currently turned off. No automatic adjustments will be made.<\/li>\n\n\n\n
  • Ready<\/strong>
    The system is prepared to activate weight control but has not started adjusting yet. The reference data is set, and the system is standing by.<\/li>\n\n\n\n
  • Weight Control is active<\/strong>
    The function is fully operational. Reference values are valid, and the system is actively adjusting parameters to stabilize part weight.<\/li>\n\n\n\n
  • Inactive \/ Injection Recipe Data Change \/ New Reference Shot Needed<\/strong>
    The function is temporarily inactive due to one of the following reasons:\n
      \n
    • No reference data is available<\/li>\n\n\n\n
    • Injection parameters (such as speed, pressure, or time) have been changed<\/li>\n\n\n\n
    • A new reference shot must be set to resume weight control<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n\n\n\n

      <\/p>\n\n\n\n

      Cycle Data<\/h4>\n\n\n\n
      \"\"<\/figure>\n\n\n\n
        \n
      • Actual Cycle<\/strong>
        Displays real-time data from the currently running cycle. All values begin at zero at the start of each cycle and update as the cycle progresses.<\/li>\n<\/ul>\n\n\n\n
          \n
        • Last Cycle<\/strong>
          After the injection process is completed, the data from the Actual Cycle<\/strong> is automatically copied here.<\/li>\n<\/ul>\n\n\n\n
            \n
          • Reference Cycle <\/strong>\n
              \n
            • With the button “Set Reference Cycle”, the value on “Last Cycle” will be copied to “Reference Cycle”. <\/li>\n\n\n\n
            • Reference Cycle contains the predefined reference values used to stabilize product weight. These target values help ensure consistent shot weight.<\/li>\n<\/ul>\n<\/li>\n\n\n\n
            • Button : Set Reference Cycle <\/strong>\n
                \n
              • \uadf8\ub9cc\ud07c Set Reference Cycle<\/strong> button is used to copy the data from the Last Cycle<\/strong> into the Reference Cycle<\/strong>.<\/li>\n\n\n\n
              • \ubaa9\uc801\n
                  \n
                • This function is used to update the reference values that help stabilize the product weight and ensure consistent quality during production.<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n\n\n\n

                  <\/p>\n\n\n\n

                  Button : Set Reference Cycle <\/strong><\/h4>\n\n\n\n
                  \"\"<\/figure>\n\n\n\n
                    \n
                  • \uadf8\ub9cc\ud07c Set Reference Cycle<\/strong> button is used to copy the data from the Last Cycle<\/strong> into the Reference Cycle<\/strong>.<\/li>\n\n\n\n
                  • Purpose:<\/strong>\n
                      \n
                    • This function is used to update the reference values that help stabilize the product weight and ensure consistent quality during production.<\/li>\n<\/ul>\n<\/li>\n\n\n\n
                    • When to Use:<\/strong>\n
                        \n
                      • After a stable and acceptable injection cycle has been completed<\/li>\n\n\n\n
                      • When setting up a new mold or production condition<\/li>\n\n\n\n
                      • When any injection parameters are changed<\/li>\n<\/ul>\n<\/li>\n\n\n\n
                      • How It Works:<\/strong>\n
                          \n
                        • Complete an injection cycle with satisfactory results.<\/li>\n\n\n\n
                        • Review the values in the Last Cycle<\/strong> column.<\/li>\n\n\n\n
                        • \ud074\ub9ad\ud558\uc138\uc694 Set Reference Cycle<\/strong> button.<\/li>\n\n\n\n
                        • The values from Last Cycle<\/strong> will be copied to Reference Cycle<\/strong> and used as the new target for weight control.<\/li>\n<\/ul>\n<\/li>\n<\/ul>\n\n\n\n

                          <\/p>\n\n\n\n

                          Adjustment Method and Intervention Limits<\/h4>\n\n\n\n
                          \"\"<\/figure>\n\n\n\n

                          This section allows the user to select automatic adjustment method and set intervention limits for the process.<\/p>\n\n\n\n

                          Adjustment Method<\/strong><\/h5>\n\n\n\n
                            \n
                          • \u2705<\/strong> Adjust Switchover Point<\/strong>
                            When this option is enabled, the system is allowed to automatically adjust the switchover position<\/strong> during the injection phase.\n
                              \n
                            • If the switchover type is position-based<\/strong>, the value will be adjusted in millimeters (mm).<\/li>\n\n\n\n
                            • If the switchover type is time-based<\/strong>, the input field changes to reflect a time setting (seconds).<\/li>\n<\/ul>\n<\/li>\n\n\n\n
                            • \u2705 Adjust Holding Pressure Level<\/strong>
                              When this option is enabled, the system is allowed to automatically adjust the holding pressure level<\/strong> during the packing phase. The adjustment is made in percentage (%) relative to the current setting.<\/li>\n<\/ul>\n\n\n\n
                              Intervention Limits<\/strong><\/h5>\n\n\n\n
                                \n
                              • Defines the maximum range within which automatic adjustments are allowed.<\/li>\n\n\n\n
                              • \uc744 \uc704\ud55c holding pressure<\/strong>, the limit is shown as a percentage (e.g., 10.0%<\/strong>), meaning the function can increase or decrease the holding pressure level by up to 10% from the user setting.<\/li>\n\n\n\n
                              • \uc744 \uc704\ud55c switchover point<\/strong>, if enabled, the limit is shown in millimeters (e.g., 10.0 mm<\/strong>) or seconds depending on the switchover type.<\/li>\n<\/ul>\n\n\n\n

                                <\/p>\n\n\n\n

                                Trend Graph \u2013 Switchover Point & Holding Pressure Adjustment<\/h4>\n\n\n\n
                                \"\"<\/figure>\n\n\n\n

                                This graph shows the trend of the last 25 production cycles<\/strong>, visualizing how the system has automatically adjusted process parameters to stabilize product weight.<\/p>\n\n\n\n

                                Switchover Point Adjustment<\/strong><\/h5>\n\n\n\n
                                  \n
                                • The graph displays the adjusted switchover position<\/strong> for each of the last 25 cycles.<\/li>\n\n\n\n
                                • \uadf8\ub9cc\ud07c current adjusted switchover point<\/strong> is 49.96 mm<\/strong>, with a difference of -0.64 mm<\/strong> compared to the user-defined reference value(50mm).<\/li>\n\n\n\n
                                • This means the system has reduced the switchover point slightly to stabilize product weight. <\/li>\n<\/ul>\n\n\n\n
                                  Holding Pressure Adjustment<\/strong><\/h5>\n\n\n\n
                                    \n
                                  • This graph displays how much the holding pressure<\/strong> was adjusted (as a percentage) relative to the user setting.<\/li>\n\n\n\n
                                  • In this example, the system applied a consistent -10.00% holding pressure adjustment<\/strong>, indicating that a lower pressure was used to maintain stable part weight.<\/li>\n<\/ul>\n\n\n\n
                                    Cycle Range Selector<\/strong><\/h5>\n\n\n\n
                                      \n
                                    • \uadf8\ub9cc\ud07c slider<\/strong> below the graph allows users to change the number of displayed cycles, ranging from 25 to 250<\/strong>.<\/li>\n\n\n\n
                                    • This helps in analyzing short-term or long-term trends in parameter adjustments.<\/li>\n<\/ul>\n\n\n\n

                                      <\/p>\n\n\n\n

                                      Button “Reset All”<\/strong><\/h4>\n\n\n\n
                                      \"\"<\/figure>\n\n\n\n

                                      \uadf8\ub9cc\ud07c Reset All<\/strong> button is used to initialize<\/strong> all stored data and reference cycle data.<\/p>\n\n\n\n

                                      Functionality:<\/strong><\/h5>\n\n\n\n
                                        \n
                                      • Clears all historical data<\/strong> on the trends.<\/li>\n\n\n\n
                                      • Resets the Reference Cycle<\/strong> values.<\/li>\n\n\n\n
                                      • Useful for starting fresh after process changes, mold changes.<\/li>\n<\/ul>\n\n\n\n

                                        Important Note:<\/strong>
                                        Use this function with caution, as all current reference data and adjustment history will be permanently deleted.<\/p>","protected":false},"excerpt":{"rendered":"

                                        Page Overview Contents \u2705 Enable of the function Status of the function This status message shows the current state of […]<\/p>\n","protected":false},"author":13,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","theme-transparent-header-meta":"","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"default","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"var(--ast-global-color-4)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"footnotes":""},"categories":[318,381,1],"tags":[],"class_list":["post-2633","post","type-post","status-publish","format-standard","hentry","category-imm-a5","category-imm-a5-manual","category-uncategorized"],"_links":{"self":[{"href":"https:\/\/www.woojin.help\/ko\/wp-json\/wp\/v2\/posts\/2633","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.woojin.help\/ko\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.woojin.help\/ko\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.woojin.help\/ko\/wp-json\/wp\/v2\/users\/13"}],"replies":[{"embeddable":true,"href":"https:\/\/www.woojin.help\/ko\/wp-json\/wp\/v2\/comments?post=2633"}],"version-history":[{"count":2,"href":"https:\/\/www.woojin.help\/ko\/wp-json\/wp\/v2\/posts\/2633\/revisions"}],"predecessor-version":[{"id":2644,"href":"https:\/\/www.woojin.help\/ko\/wp-json\/wp\/v2\/posts\/2633\/revisions\/2644"}],"wp:attachment":[{"href":"https:\/\/www.woojin.help\/ko\/wp-json\/wp\/v2\/media?parent=2633"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.woojin.help\/ko\/wp-json\/wp\/v2\/categories?post=2633"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.woojin.help\/ko\/wp-json\/wp\/v2\/tags?post=2633"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}