{"id":3645,"date":"2025-12-04T14:42:27","date_gmt":"2025-12-04T14:42:27","guid":{"rendered":"https:\/\/www.woojin.help\/?p=3645"},"modified":"2026-01-29T12:10:05","modified_gmt":"2026-01-29T12:10:05","slug":"machine-setup-parameters-dla5-imc510-uftag510-01","status":"publish","type":"post","link":"https:\/\/www.woojin.help\/ko\/machine-setup-parameters-dla5-imc510-uftag510-01\/","title":{"rendered":"Machine Setup Parameters (DLA5, IMC510, UF510.1, UF510.3)"},"content":{"rendered":"
<\/div>\n

Clamp General<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Sensor Type<\/td>SSI<\/td> <\/td><\/tr>
Actuator Type<\/td>Hydraulic<\/td> <\/td><\/tr>
Minimum Stroke<\/td>0.0 mm<\/td> <\/td><\/tr>
Maximum Stroke<\/td>1750.0<\/td>Depends on the size of the machine<\/td><\/tr>
Filter Time (Velocity Measurement)<\/td>5 ms<\/td> <\/td><\/tr>
Pump number<\/td>Servo Pump 1<\/td> <\/td><\/tr>
1st Step Release Pressure<\/td>25 bar<\/td> <\/td><\/tr>
End Release Pressure<\/td>10 bar<\/td> <\/td><\/tr>
Resolution of Sensor<\/td>1 \u00b5m<\/td> <\/td><\/tr>
Maximum Sensor pressure<\/td>250 bar<\/td>It depends on which sensor is used, so what its maximum bar is at 10,000 mV<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Spring Mold Options<\/h3>\n\n\n\n

Turn to ON only if you use Spring Molds.<\/p>\n\n\n\n

Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Enable<\/td>OFF<\/td>Set to ON only if you use a Spring Mold\ufeff<\/td><\/tr>
Motor velocity<\/td>200 rpm<\/td> <\/td><\/tr>
Mold Valve Open<\/td>1500 mV<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Set clamping force range during injection, Friction Test Settings, Clamping Force Sensor, Clamping Force Sensor 2, Clamping Force Sensor 3, Clamping Force Sensor 4 = Set the value to 0<\/p>\n\n\n\n

Close 2<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Factor Lock Reference Pressure<\/td>1 bar<\/td> <\/td><\/tr>
Lock Pressure pre switch.<\/td>0 bar<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Mold Open<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Acceleration Velocity Rate<\/td>1500 mm\/s\u00b2<\/td> <\/td><\/tr>
Acceleration Pressure Rate<\/td>3000 mm\/s\u00b2<\/td> <\/td><\/tr>
Deceleration Velocity Rate<\/td>3000 mm\/s\u00b2<\/td> <\/td><\/tr>
Slow pressure rate<\/td>500 mm\/s\u00b2<\/td> <\/td><\/tr>
End Deceleration SPD Rate<\/td>2000 \u2013 3000 mm\/s\u00b2<\/td> <\/td><\/tr>
End of PRS velocity reduction rate<\/td>Not used = 32767<\/td> <\/td><\/tr>
Stop rate reduction SPD<\/td>2000 mm\/s\u00b2<\/td> <\/td><\/tr>
Stop reducing PRS rates<\/td>Not used =32767<\/td> <\/td><\/tr>
Delay time compensation<\/td>70 ms<\/td> <\/td><\/tr>
VP output delay<\/td>100 ms<\/td> <\/td><\/tr>
Next movement delay<\/td>400 ms<\/td>Important for PlaimmX Programs<\/td><\/tr>
Setting Mode Velocity<\/td>40 mm\/s<\/td> <\/td><\/tr>
Setting Mode Pressure<\/td>40 \u2013 100 bar<\/td>*<\/td><\/tr>
Position-Tolerance<\/td>10.0 mm<\/td> <\/td><\/tr>
Tolerance time<\/td>3000 ms<\/td> <\/td><\/tr>
Maximum Velocity<\/td>700 mm\/s<\/td> <\/td><\/tr>
Motor velocity at maximum velocity<\/td>750 rpm<\/td> <\/td><\/tr>
Maximum Pressure<\/td>200 bar<\/td> <\/td><\/tr>
Pump pressure at maximum pressure<\/td>175 bar<\/td> <\/td><\/tr>
Minimum Pressure (Mold Open)<\/td>25.0 bar<\/td> <\/td><\/tr>
Maximum Velocity(Pump Only)<\/td>1440 mm\/s<\/td> <\/td><\/tr>
Deceleration Velocity Rate Valve<\/td>0.0 mm<\/td> <\/td><\/tr>
End Deceleration SPD Rate Valve<\/td>0.0 mm<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

* The Setting Mode will be adjusted again through the Setting Mode Controller. If the bar count is too low, the mold will no longer move to or away from its position. This applies to each axis that is held in the Setting Mode Controller. For example DL650A5 –> Woojin Plaimm Austria<\/p>\n\n\n\n

End Deceleration Rate<\/h3>\n\n\n\n
Deceleration (Velocity\/Deceleration)<\/td>%<\/td>mm\/s\u00b2<\/td><\/tr>
Deceleration #1 (Velocity\/Deceleration)<\/td>0<\/td>600<\/td><\/tr>
Deceleration #2 (Velocity\/Deceleration)<\/td>25<\/td>1000<\/td><\/tr>
Deceleration #3 (Velocity\/Deceleration)<\/td>50<\/td>1500<\/td><\/tr>
Deceleration #4 (Velocity\/Deceleration)<\/td>100<\/td>2000 – 3000<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Mold closure<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Acceleration Velocity Rate<\/td>1000 mm\/s\u00b2<\/td> <\/td><\/tr>
Acceleration Pressure Rate<\/td>4000 mm\/s\u00b2<\/td> <\/td><\/tr>
Deceleration Velocity Rate<\/td>3000 mm\/s\u00b2<\/td> <\/td><\/tr>
Slow pressure rate<\/td>3000 mm\/s\u00b2<\/td> <\/td><\/tr>
End Deceleration SPD Rate<\/td>1100 — 1500 mm\/s\u00b2<\/td> <\/td><\/tr>
End of PRS velocity reduction rate<\/td>3000 mm\/s\u00b2<\/td> <\/td><\/tr>
Stop rate reduction SPD<\/td>1000 mm\/s\u00b2<\/td> <\/td><\/tr>
Stop reducing PRS rates<\/td>1000 mm\/s\u00b2<\/td> <\/td><\/tr>
Delay time compensation<\/td>80 ms<\/td> <\/td><\/tr>
VP output delay<\/td>150 ms<\/td> <\/td><\/tr>
Next movement delay<\/td>500 ms<\/td>Important for PlaimmX Programs<\/td><\/tr>
Setting Mode delay<\/td>40 mm\/s<\/td> <\/td><\/tr>
Setting Mode Pressure<\/td>40 – 100 bar<\/td>*<\/td><\/tr>
Position-Tolerance<\/td>1.0 — 3.00 mm<\/td> <\/td><\/tr>
Tolerance time<\/td>3000 ms<\/td> <\/td><\/tr>
Jolt Time<\/td>50  ms<\/td> <\/td><\/tr>
Maximum Velocity<\/td>700 mm\/s<\/td> <\/td><\/tr>
Motor velocity at maximum velocity<\/td>700 rpm<\/td> <\/td><\/tr>
Maximum Pressure<\/td>200 bar<\/a><\/td> <\/td><\/tr>
Pump pressure at maximum pressure<\/td>175 bar<\/td> <\/td><\/tr>
Minimum Position Limit<\/td>-4.0 bar<\/td> <\/td><\/tr>
Maximum Velocity<\/td>658 mm\/s<\/td> <\/td><\/tr>
End time shaking<\/td>0 ms<\/td> <\/td><\/tr>
Slow velocity locking mold<\/td>40.0 mm\/s<\/td> <\/td><\/tr>
Slow pressure locking mold<\/td>150 bar<\/td> <\/td><\/tr>
Slow mold locking position<\/td>0.0 mm<\/td> <\/td><\/tr>
2-3 Stage Maximum Pressure<\/td>175 bar<\/td> <\/td><\/tr>
Maximum velocity (MP)<\/td>2000 mm\/s<\/td> <\/td><\/tr>
Maximum Pressure (MP)<\/td>175 bar<\/td> <\/td><\/tr>
Maximum velocity (Lock)<\/td>1000 mm\/s<\/td> <\/td><\/tr>
Maximum Pressure(Lock)<\/td>175 bar<\/td> <\/td><\/tr>
Mold Lock Delay<\/td>20 ms<\/td> <\/td><\/tr>
Mold Lock Time<\/td>150 ms<\/td> <\/td><\/tr>
Stop Deceleration Mold Protection<\/td>2000 mm\/s\u00b2<\/td> <\/td><\/tr>
Mold HP Maximum Start Position<\/td>10.0 mm<\/td> <\/td><\/tr>
Acce \/ Decel Mold HP<\/td>800 mm\/s\u00b2<\/td> <\/td><\/tr>
Mold HP Tolerance<\/td>10 bar<\/td> <\/td><\/tr>
Acceleration Mold HP<\/td>1000 mm\/s\u00b2<\/td> <\/td><\/tr>
Deceleration Mold HP<\/td>600 mm\/s\u00b2<\/td> <\/td><\/tr>
Deceleration Pressure Mold HP<\/td>0.20 s<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

* The Setting Mode will be adjusted again through the Setting Mode Controller. If the bar count is too low, the mold will no longer move to or away from its position. This applies to each axis that is held in the Setting Mode Controller. For example DL650A5 –> Woojin Plaimm Austria<\/p>\n\n\n\n

Suction Valve (Filling Valve)<\/h3>\n\n\n\n

SuctionValve Delay Time, Suction Valve Close Pressure, Suction Valve Close Time, Suction Valve Close Velocity, Suction Valve Close Position = 0<\/p>\n\n\n\n

Deceleration (Velocity\/Deceleration)<\/td>%<\/td>mm\/s\u00b2<\/td><\/tr>
Deceleration #1 (Velocity\/Deceleration)<\/td>10<\/td>400<\/td><\/tr>
Deceleration #2 (Velocity\/Deceleration)<\/td>25<\/td>600<\/td><\/tr>
Deceleration #3 (Velocity\/Deceleration)<\/td>50<\/td>900<\/td><\/tr>
Deceleration #4 (Velocity\/Deceleration)<\/td>100<\/td>1100 – 2100<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Setting Mode Controller<\/h3>\n\n\n\n
Movement<\/td>Velocity (actual value) mm\/s<\/td>Velocity (set-Value) %<\/td>Pressure (actual value) mm\/s<\/td>Pressure (set-Value) %<\/td><\/tr>
Mold Close<\/td>40<\/td>100<\/td>50<\/td>100<\/td><\/tr>
Mold Open<\/td>40<\/td>100<\/td>60<\/td>100<\/td><\/tr>
Ejector advance<\/td>60<\/td>100<\/td>60<\/td>100<\/td><\/tr>
Ejector retract<\/td>30<\/td>100<\/td>60<\/td>100<\/td><\/tr>
Carriage forward<\/td>10<\/td>100<\/td>50<\/td>100<\/td><\/tr>
Carriage backward<\/td>10<\/td>100<\/td>50<\/td>100<\/td><\/tr>
Injection<\/td>50<\/td>100<\/td>60<\/td>100<\/td><\/tr>
Decompression<\/td>10<\/td>100<\/td>35<\/td>100<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Ejection General Settings<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Sensor Type<\/td>POT<\/td> <\/td><\/tr>
Actuator Type<\/td>Hydraulic<\/td> <\/td><\/tr>
Minimum Stroke<\/td>0.0 mm<\/td> <\/td><\/tr>
Maximum Stroke<\/td>255.0 mm<\/td>Depends on the size of the machine<\/td><\/tr>
Maximum Use Stroke<\/td>250.0 mm<\/td>Depends on the size of the machine<\/td><\/tr>
Cylinder Area Forward<\/td>104.0 cm\u00b3<\/td>Depends on the size of the machine<\/td><\/tr>
Cylinder Area Backward<\/td>60.0 cm\u00b3<\/td>Depends on the size of the machine<\/td><\/tr>
Filter Time<\/td>40 ms<\/td> <\/td><\/tr>
Pump number<\/td>2<\/td> <\/td><\/tr>
Control Step<\/td> <\/td> <\/td><\/tr>
Maximum allowed ejector backward end position (Rotarv Table onlv)<\/td>0.0 mm<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Ejector Retract<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Acceleration Velocity Rate<\/td>18000 mm\/s\u00b2<\/td> <\/td><\/tr>
Acceleration Pressure Rate<\/td>1500 mm\/s\u00b2<\/td> <\/td><\/tr>
Deceleration Velocity Rate<\/td>2000 mm\/s\u00b2<\/td> <\/td><\/tr>
End Deceleration SPD Rate<\/td>2000 mm\/s\u00b2<\/td> <\/td><\/tr>
Delay time compensation<\/td>140 ms<\/td> <\/td><\/tr>
VP output delay<\/td>80 ms<\/td> <\/td><\/tr>
Next movement delay<\/td>400 ms<\/td> <\/td><\/tr>
Setting Mode Velocity<\/td>30.0 mm\/s<\/td> <\/td><\/tr>
Setting Mode Pressure<\/td>60 bar<\/td> <\/td><\/tr>
Position-Tolerance<\/td>1.0 mm<\/td> <\/td><\/tr>
Tolerance time<\/td>3000 ms<\/td> <\/td><\/tr>
Jolt time<\/td>1 ms<\/td> <\/td><\/tr>
Maximum Velocity<\/td>200.0 mm\/s<\/td> <\/td><\/tr>
Motor velocity at maximum Velocity<\/td>1750 rpm<\/td> <\/td><\/tr>
Maximum Pressure<\/td>175 bar<\/td> <\/td><\/tr>
Pump pressure at maximum press.<\/td>175 bar<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Ejector Advance<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Acceleration Velocity Rate<\/td>1800 mm\/s\u00b2<\/td> <\/td><\/tr>
Acceleration Pressure Rate<\/td>1500 mm\/s\u00b2<\/td> <\/td><\/tr>
Deceleration Velocity Rate<\/td>2000 mm\/s\u00b2<\/td> <\/td><\/tr>
End Deceleration SPD Rate<\/td>1500 mm\/s\u00b2<\/td> <\/td><\/tr>
Delay time compensation<\/td>140 ms<\/td> <\/td><\/tr>
VP output delay<\/td>50 ms<\/td> <\/td><\/tr>
Next movement delay<\/td>400 ms<\/td> <\/td><\/tr>
Setting Mode Velocity<\/td>60.0 mm\/s<\/td> <\/td><\/tr>
Setting Mode Pressure<\/td>60 bar<\/td> <\/td><\/tr>
Position-Tolerance<\/td>1.0 mm<\/td> <\/td><\/tr>
Tolerance time<\/td>3000 ms<\/td> <\/td><\/tr>
Jolt time<\/td>1 ms<\/td> <\/td><\/tr>
Maximum Velocity<\/td>200.0 mm\/s<\/td> <\/td><\/tr>
Motor velocity at maximum Velocity<\/td>1750 rpm<\/td> <\/td><\/tr>
Maximum Pressure<\/td>175 bar<\/td> <\/td><\/tr>
Pump pressure at maximum press.<\/td>175 bar<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Inejction<\/h3>\n\n\n\n

Pressure Controler<\/p>\n\n\n\n

Parameter<\/td>Value Range<\/td><\/tr>
Proportional Gain – Kp<\/td>30.000<\/td><\/tr>
Integralverst. – Ki<\/td>0.000<\/td><\/tr>
Derivative Ampl. – Kd<\/td>0.000<\/td><\/tr>
Hold On velocity<\/td>350.0 mm\/s<\/td><\/tr>
Hold On Press Ramp<\/td>1000 mm\/s\u00b2<\/td><\/tr>
Hold on joint time<\/td>300 ms<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Velocity Controller<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td><\/tr>
Injection Velocity Control<\/td>CLOSED LOOP<\/td><\/tr>
Proportional Gain – Kp<\/td>0.500<\/td><\/tr>
Integralverst. – Ki<\/td>20.000<\/td><\/tr>
Derivative Ampl. – Kd<\/td>0.000<\/td><\/tr>
Open loop part<\/td>0<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n
Parameter<\/td>Value Range<\/td><\/tr>
Valve Type<\/td>Pump<\/td><\/tr>
Injection Maximum Voltage<\/td>10000 mV<\/td><\/tr>
Injection Minimum Voltage<\/td>0 mV<\/td><\/tr>
Holding Pressure Maximum Voltage<\/td>10000 mV<\/td><\/tr>
Holding Pressure Minimum Voltage<\/td>0 mV<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Pump Selection: Each value is 0<\/p>\n\n\n\n

Charge Valve Setting<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td><\/tr>
Value Typ<\/td>PROPORTIONAL<\/td><\/tr>
Back-pressure Maximum Voltage<\/td>10000 mV<\/td><\/tr>
Back-pressure Minimum Voltage<\/td>0 mV<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

ACC SETTING = Each value is 0; Injection Hydraulic Type IH23. It\u2019s the same on the third INJECTION Page<\/p>\n\n\n\n

INJECTION Page<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Sensor Type<\/td>SSI<\/td> <\/td><\/tr>
Actuator Type<\/td>Hydraulic<\/td> <\/td><\/tr>
Minimum Stroke<\/td>0.0 mm<\/td> <\/td><\/tr>
Maximum Stroke<\/td>495.0 mm<\/td>The maximum stroke depends on the size of the built-in cylinder.<\/td><\/tr>
Filter Time (Velocity Measurement)<\/td> <\/td> <\/td><\/tr>
Resolution of sensor<\/td>1.0 \u00b5m<\/td> <\/td><\/tr>
Pump number<\/td>Servo Pump<\/td> <\/td><\/tr>
Filter Time (Pressure)<\/td>1<\/td> <\/td><\/tr>
Ratio<\/td>10000.0<\/td> <\/td><\/tr>
Maximum Sensor pressure<\/td>250 kg\/cm\u00b2<\/td>It depends on which sensor is used, so what its maximum bar is at 10,000 mV<\/td><\/tr>
Minimum voltage (Sensor)<\/td>0.0 mV<\/td> <\/td><\/tr>
Maximum voltage (Sensor)<\/td>10000.0 mV<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Linearization of injection speed<\/h3>\n\n\n\n

Linearization of injection speed is shown in the table starting with the maximum power of the pump in our case 2000 rpm = 100%. Then, in our case, we go from 200 rpm down to 10%.<\/p>\n\n\n\n

Set 10%<\/td>200 rpm<\/td><\/tr>
Set 20%<\/td>400 rpm<\/td><\/tr>
Set 30%<\/td>600 rpm<\/td><\/tr>
Set 40%<\/td>800 rpm<\/td><\/tr>
Set 50%<\/td>1000 rpm<\/td><\/tr>
Set 60%<\/td>1200 rpm<\/td><\/tr>
Set 70%<\/td>1400 rpm<\/td><\/tr>
Set 80%<\/td>1600 rpm<\/td><\/tr>
Set 90%<\/td>1800 rpm<\/td><\/tr>
Set 100%<\/td>2000 rpm<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Injection (3.)<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Acceleration Velocity Rate<\/td>2000 mm\/s\u00b2<\/td> <\/td><\/tr>
Acceleration Pressure Rate<\/td>1500 mm\/s\u00b2<\/td> <\/td><\/tr>
Deceleration Velocity Rate<\/td>2000 mm\/s\u00b2<\/td> <\/td><\/tr>
End Deceleration SPD Rate<\/td>500 mm\/s\u00b2<\/td> <\/td><\/tr>
Delay time compensation<\/td>5 ms<\/td> <\/td><\/tr>
VP output delay<\/td>1 ms<\/td> <\/td><\/tr>
Next movement delay<\/td>500 ms<\/td>Important for PlaimmX Programs<\/td><\/tr>
Setting Mode Velocity<\/td>50 mm\/s<\/td> <\/td><\/tr>
Setting Mode Pressure<\/td>60 bar<\/td>*<\/td><\/tr>
Position-Tolerance<\/td>5.0 mm<\/td> <\/td><\/tr>
Holding Pressure Maximum Value<\/td>175 bar<\/td> <\/td><\/tr>
Jolt Time<\/td>5.0 ms<\/td> <\/td><\/tr>
Maximum Velocity<\/td>109 mm\/s<\/td> <\/td><\/tr>
Motor velocity at maximum velocity<\/td>2000 rpm<\/td> <\/td><\/tr>
Maximum Pressure<\/td>175 bar<\/td> <\/td><\/tr>
Pump pressure at maximum pressure<\/td>175 bar<\/td> <\/td><\/tr>
Use Injection differential<\/td>OFF<\/td> <\/td><\/tr>
Injection differential Velocity<\/td>509.3 mm\/s<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Decompression:<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Acceleration Velocity Rate<\/td>2000 mm\/s\u00b2<\/td> <\/td><\/tr>
Acceleration Pressure Rate<\/td>2000 mm\/s\u00b2<\/td> <\/td><\/tr>
Deceleration Velocity Rate<\/td>500 mm\/s\u00b2<\/td> <\/td><\/tr>
End Deceleration SPD Rate<\/td>50 mm\/s\u00b2<\/td> <\/td><\/tr>
Delay time compensation<\/td>5 ms<\/td> <\/td><\/tr>
VP output delay<\/td>100 ms<\/td> <\/td><\/tr>
Next movement delay<\/td>100 ms<\/td>Important for PlaimmX Programs<\/td><\/tr>
Setting Mode Velocity<\/td>10 mm\/s<\/td> <\/td><\/tr>
Setting Mode Pressure<\/td>35 bar<\/td>*<\/td><\/tr>
Position-Tolerance<\/td>10.0 mm<\/td> <\/td><\/tr>
Jolt Time<\/td>10.0 ms<\/td> <\/td><\/tr>
Maximum Velocity<\/td>70 mm\/s<\/td> <\/td><\/tr>
Motor velocity at maximum velocity<\/td>1700 rpm<\/td> <\/td><\/tr>
Maximum Pressure<\/td>175 bar<\/td> <\/td><\/tr>
Pump pressure at maximum pressure<\/td>175 bar<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

ROTATION CONTROLLER<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Proportional Gain – Kp<\/td>0.000<\/td> <\/td><\/tr>
Integralverst. – Ki<\/td>0.000<\/td> <\/td><\/tr>
Derivative Ampl. – Kd<\/td>0.000<\/td> <\/td><\/tr>
Open loop part<\/td>0<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Charge Main Pressure Setting<\/p>\n\n\n\n

Charge Pressure = 150 bar<\/p>\n\n\n\n

Charge<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Acceleration Velocity Rate<\/td>2000 mm\/s\u00b2<\/td> <\/td><\/tr>
Acceleration Pressure Rate<\/td>12000 mm\/s\u00b2<\/td> <\/td><\/tr>
End Deceleration SPD Rate<\/td>8000 mm\/s\u00b2<\/td> <\/td><\/tr>
Delay time compensation<\/td>2 ms<\/td> <\/td><\/tr>
VP output delay<\/td>100 ms<\/td> <\/td><\/tr>
Next movement delay<\/td>300 ms<\/td>Important for PlaimmX Programs<\/td><\/tr>
Setting Mode Velocity<\/td>50 mm\/s<\/td> <\/td><\/tr>
Setting Mode Pressure<\/td>100 bar<\/td>*<\/td><\/tr>
Position-Tolerance<\/td>0.1 mm<\/td> <\/td><\/tr>
Tolerance time<\/td>3000 ms<\/td> <\/td><\/tr>
Jolt Time<\/td>1 ms<\/td> <\/td><\/tr>
Maximum Velocity<\/td>150 rpm<\/td> <\/td><\/tr>
Motor velocity at maximum velocity<\/td>1895 rpm<\/td> <\/td><\/tr>
Maximum Pressure<\/td>175 bar<\/td> <\/td><\/tr>
Pump pressure at maximum pressure<\/td>175 bar<\/td> <\/td><\/tr>
Number of Teeth<\/td>12<\/td> <\/td><\/tr>
Maximum RPM in Parallel<\/td>160.0 rpm<\/td> <\/td><\/tr>
Maximum motor velocity in parall.<\/td>0 rpm<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Pump Selection Table<\/p>\n\n\n\n

Every value in the table is = 0<\/p>\n\n\n\n

Backpressure Controller<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Proportional Gain – Kp<\/td>5.000<\/td> <\/td><\/tr>
Integralverst. – Ki<\/td>0.000<\/td> <\/td><\/tr>
Derivative Ampl. – Kd<\/td>0.000<\/td> <\/td><\/tr>
Maximum Velocity<\/td>0.00 mm\/s<\/td> <\/td><\/tr>
BACKPRESS JOLT TIME<\/td>10000 mm\/s\u00b2<\/td> <\/td><\/tr>
Backpressure Maximum<\/td>0 ms<\/td> <\/td><\/tr>
Maximum Stroke<\/td>50 bar<\/td> <\/td><\/tr>
Sensor Type<\/td>POT<\/td> <\/td><\/tr>
Actuator Type<\/td>Hydraulic<\/td> <\/td><\/tr>
Back Pressure In Manual<\/td>0 bar<\/td> <\/td><\/tr>
Injection Pressure<\/td>bar<\/td>Current value display<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

CHARGE HYBRID SETTING<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Main Velocity Output<\/td>0 mV<\/td> <\/td><\/tr>
Main Pressure Output<\/td>0 mV<\/td> <\/td><\/tr>
IP Hybrid Axis<\/td>IP 1<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

LINEAR INITIALIZE<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Velocity Linearization<\/td>OFF<\/td> <\/td><\/tr>
Pressure Linearization<\/td>OFF<\/td> <\/td><\/tr>
Back-Pressure Linearization<\/td>OFF<\/td> <\/td><\/tr>
Velocity 2 Linearization<\/td>OFF<\/td> <\/td><\/tr>
Pressure 2 Linearization<\/td>OFF<\/td> <\/td><\/tr>
Back Pressure Control<\/td>CLOSED LOOP<\/td> <\/td><\/tr>
Proportional Gain – Kp<\/td>5.000<\/td> <\/td><\/tr>
Integralverst. – Ki<\/td>0.000<\/td> <\/td><\/tr>
Derivative Ampl. – Kd<\/td>0.000<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Carriage<\/h2>\n\n\n\n

General<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Sensor Type<\/td>POT<\/td> <\/td><\/tr>
Actuator Type<\/td>Hydraulic<\/td> <\/td><\/tr>
Minimum Stroke<\/td>0.0 mm<\/td> <\/td><\/tr>
Maximum Stroke<\/td>500 mm<\/td> <\/td><\/tr>
Filter Time (Velocity Measurement)<\/td>40 ms<\/td> <\/td><\/tr>
Pump number<\/td>Servo Pump<\/td> <\/td><\/tr>
Idle Output Point<\/td>0<\/td> <\/td><\/tr>
Ratio<\/td>10000.0<\/td> <\/td><\/tr>
Maximum Sensor pressure<\/td>250 Bar<\/td>It depends on which sensor is used, so what its maximum bar is at 10,000 mV<\/td><\/tr>
Minimum voltage (Sensor)<\/td>0.0 mV<\/td> <\/td><\/tr>
Maximum voltage (Sensor)<\/td>10000.0 mV<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Additional Settings<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Use the Advance Keep Pressure<\/td>OFF  <\/td> <\/td><\/tr>
Advance Velocity Limit<\/td>200 mm\/s<\/td> <\/td><\/tr>
Retract Velocity Limit<\/td>280 mm\/s<\/td> <\/td><\/tr>
Maximum Contact pressure<\/td>100 bar<\/td> <\/td><\/tr>
Offset Pressure<\/td>10 bar<\/td> <\/td><\/tr>
Carriage Forward 2nd Velocity<\/td>25 %<\/td> <\/td><\/tr>
Confirm Carriage touch Position<\/td>60 bar<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Carriage Forward<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Acceleration Velocity Rate<\/td>1000 mm\/s\u00b2<\/td> <\/td><\/tr>
Acceleration Pressure Rate<\/td>5000 mm\/s\u00b2<\/td> <\/td><\/tr>
Deceleration Velocity Rate<\/td>1000 mm\/s\u00b2<\/td> <\/td><\/tr>
End Deceleration SPD Rate<\/td>500 mm\/s\u00b2<\/td> <\/td><\/tr>
Delay time compensation<\/td>25 ms<\/td> <\/td><\/tr>
VP output delay<\/td>10 ms<\/td> <\/td><\/tr>
Next movement delay<\/td>10 ms<\/td> <\/td><\/tr>
Setting Mode Velocity<\/td>10 mm\/s<\/td> <\/td><\/tr>
Setting Mode Pressure<\/td>50 bar<\/td>*<\/td><\/tr>
Position-Tolerance<\/td>5.0 mm<\/td> <\/td><\/tr>
Tolerance time<\/td>3000 ms<\/td> <\/td><\/tr>
Touch Delay<\/td>100.0 ms<\/td> <\/td><\/tr>
Maximum Velocity<\/td>200 mm\/s<\/td> <\/td><\/tr>
Motor velocity at maximum velocity<\/td>500 rpm<\/td> <\/td><\/tr>
Maximum Pressure<\/td>175 bar<\/td> <\/td><\/tr>
Pump pressure at maximum pressure<\/td>175 bar<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Carriage Backward<\/h3>\n\n\n\n
Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Acceleration Velocity Rate<\/td>1000 mm\/s\u00b2<\/td> <\/td><\/tr>
Acceleration Pressure Rate<\/td>32767 mm\/s\u00b2<\/td> <\/td><\/tr>
Deceleration Velocity Rate<\/td>1000 mm\/s\u00b2<\/td> <\/td><\/tr>
End Deceleration SPD Rate<\/td>300 mm\/s\u00b2<\/td> <\/td><\/tr>
Delay time compensation<\/td>100 ms<\/td> <\/td><\/tr>
VP output delay<\/td>10 ms<\/td> <\/td><\/tr>
Next movement delay<\/td>10 ms<\/td> <\/td><\/tr>
Setting Mode Velocity<\/td>10 mm\/s<\/td> <\/td><\/tr>
Setting Mode Pressure<\/td>50 bar<\/td>*<\/td><\/tr>
Position-Tolerance<\/td>5.0 mm<\/td> <\/td><\/tr>
Tolerance time<\/td>3000 ms<\/td> <\/td><\/tr>
Touch Delay<\/td>280.0 ms<\/td> <\/td><\/tr>
Maximum Velocity<\/td>200 mm\/s<\/td> <\/td><\/tr>
Motor velocity at maximum velocity<\/td>1100 rpm<\/td> <\/td><\/tr>
Maximum Pressure<\/td>175 bar<\/td> <\/td><\/tr>
Pump pressure at maximum pressure<\/td>175 bar<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Pump<\/h3>\n\n\n\n

Servo Pump 1 (8LSP96R2013 )<\/p>\n\n\n\n

Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Kp<\/td>10.000<\/td>Check which pumps are installed. The values now apply to BuR pumps with 96 kW. The Kp value varies depending on the manufacturer, for example in the case of KEB.<\/td><\/tr>
Tn<\/td>0.100<\/td>Check which pumps are installed. The values now apply to BuR pumps with 96 kW. The Tn value varies depending on the manufacturer, for example in the case of KEB.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Pump<\/h3>\n\n\n\n

Servo Pumpe 2 (8LSP94R2013)<\/p>\n\n\n\n

Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Kp<\/td>10.000<\/td>Check which pumps are installed. The values now apply to BuR pumps with 96 kW. The Kp value varies depending on the manufacturer, for example in the case of KEB.<\/td><\/tr>
Tn<\/td>0.100<\/td>Check which pumps are installed. The values now apply to BuR pumps with 96 kW. The Tn value varies depending on the manufacturer, for example in the case of KEB.<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Sevo Pump Parameter:<\/h3>\n\n\n\n

Servo Pump Control Mode\/ Basic parameter for servo pump<\/p>\n\n\n\n

Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
Control Mode<\/td>1<\/td>1<\/td><\/tr>
dnUp<\/td>1000.0<\/td>1000.0<\/td><\/tr>
nMax<\/td>3000.0<\/td>3000.0<\/td><\/tr>
Maximum Sensor Pressure<\/td>250<\/td>250<\/td><\/tr>
Voltage at maximum pressure<\/td>10000.0<\/td>10000.0<\/td><\/tr>
Voltage at no pressure<\/td>0.0<\/td>0.0<\/td><\/tr>
Revers<\/td>YES = Green<\/td>YES = Green<\/td><\/tr>
dnDown<\/td>1500.0<\/td>1500.0<\/td><\/tr>
Minimum Pressure<\/td>5.0 bar<\/td> <\/td><\/tr>
Filter pAct<\/td>0.000<\/td> <\/td><\/tr>
Filter pSetDown<\/td>0.000<\/td> <\/td><\/tr>
Filter pSetUp<\/td>0.000<\/td> <\/td><\/tr>
Pressure Sensor Wired **<\/td>OFF<\/td>OFF<\/td><\/tr>
Pressure Input **<\/td>Drive Input<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

** The pressure sensor Wired is set to either OFF<\/em> or ON<\/em>, and the pressure input again depends on which manufacturer is installed \u2014 whether the machine uses KEB or, as in our case, BuR<\/p>\n\n\n\n

Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
TabPara[0].Kp<\/td>10.0<\/td>10.0<\/td><\/tr>
TabPara[0].Tn<\/td>0.50<\/td>0.50<\/td><\/tr>
TabPara[0].Tv<\/td>0.025<\/td>0.025<\/td><\/tr>
TabPara[0].T1<\/td>0.02<\/td>0.02<\/td><\/tr>
TabPara[0].nRev<\/td>-100.0<\/td>-100.0<\/td><\/tr>
TabPara[0].KpMPC<\/td>0.10<\/td> <\/td><\/tr>
TabPara[0].TnMPC<\/td>0.00<\/td> <\/td><\/tr>
TabPara[0].TvMPC<\/td>0.000<\/td> <\/td><\/tr>
TabPara[0].T1MPC<\/td>0.00<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Multi parameter of pressure<\/p>\n\n\n\n

Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
TabPara[0].Kp<\/td>15.0<\/td>15.0<\/td><\/tr>
TabPara[0].Tn<\/td>0.50<\/td>0.50<\/td><\/tr>
TabPara[0].Tv<\/td>0.025<\/td>0.025<\/td><\/tr>
TabPara[0].T1<\/td>0.02<\/td>0.02<\/td><\/tr>
TabPara[0].nRev<\/td>-100.0<\/td>-100.0<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Small Parameter of Pressure<\/p>\n\n\n\n

Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
TabPara[0].Kp<\/td>15.0<\/td>15.0<\/td><\/tr>
TabPara[0].Tn<\/td>0.50<\/td>0.50<\/td><\/tr>
TabPara[0].Tv<\/td>0.025<\/td>0.025<\/td><\/tr>
TabPara[0].T1<\/td>0.02<\/td>0.02<\/td><\/tr>
TabPara[0].nRev<\/td>-500.0<\/td>-500.0<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Clamp Parameter of Pressure<\/p>\n\n\n\n

Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
TabPara[0].Kp<\/td>5.0<\/td>5.0<\/td><\/tr>
TabPara[0].Tn<\/td>0.20<\/td>0.20<\/td><\/tr>
TabPara[0].Tv<\/td>0.025<\/td>0.025<\/td><\/tr>
TabPara[0].T1<\/td>0.02<\/td>0.02<\/td><\/tr>
TabPara[0].nRev<\/td>-100.0<\/td>-100.0<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Injection Parameter of Pressure<\/p>\n\n\n\n

Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
TabPara[0].Kp<\/td>12.0<\/td>12.0<\/td><\/tr>
TabPara[0].Tn<\/td>0.18<\/td>0.18<\/td><\/tr>
TabPara[0].Tv<\/td>0.025<\/td>0.025<\/td><\/tr>
TabPara[0].T1<\/td>0.02<\/td>0.02<\/td><\/tr>
TabPara[0].nRev<\/td>-100.0<\/td>-100.0<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Holdon Parameter of Pressure<\/p>\n\n\n\n

Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
TabPara[0].Kp<\/td>10.0<\/td>10.0<\/td><\/tr>
TabPara[0].Tn<\/td>0.20<\/td>0.20<\/td><\/tr>
TabPara[0].Tv<\/td>0.025<\/td>0.025<\/td><\/tr>
TabPara[0].T1<\/td>0.02<\/td>0.02<\/td><\/tr>
TabPara[0].nRev<\/td>-100.0<\/td>-100.0<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Ejector Parameter of Pressure<\/p>\n\n\n\n

Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
TabPara[0].Kp<\/td>10.0<\/td>10.0<\/td><\/tr>
TabPara[0].Tn<\/td>0.20<\/td>0.20<\/td><\/tr>
TabPara[0].Tv<\/td>0.025<\/td>0.025<\/td><\/tr>
TabPara[0].T1<\/td>0.02<\/td>0.02<\/td><\/tr>
TabPara[0].nRev<\/td>-100.0<\/td>-100.0<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Tonnage Parameter of Pressure<\/p>\n\n\n\n

Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
TabPara[0].Kp<\/td>20.0<\/td>20.0<\/td><\/tr>
TabPara[0].Tn<\/td>0.15<\/td>0.15<\/td><\/tr>
TabPara[0].Tv<\/td>0.025<\/td>0.025<\/td><\/tr>
TabPara[0].T1<\/td>0.02<\/td>0.02<\/td><\/tr>
TabPara[0].nRev<\/td>-400.0<\/td>-400.0<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Half Nut Parameter of Pressure<\/p>\n\n\n\n

Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
TabPara[0].Kp<\/td>10.0<\/td>10.0<\/td><\/tr>
TabPara[0].Tn<\/td>0.20<\/td>0.20<\/td><\/tr>
TabPara[0].Tv<\/td>0.025<\/td>0.025<\/td><\/tr>
TabPara[0].T1<\/td>0.02<\/td>0.02<\/td><\/tr>
TabPara[0].nRev<\/td>-100.0<\/td>-100.0<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Standstill parameter of pressure<\/p>\n\n\n\n

Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
TabPara[0].Kp<\/td>5.0<\/td>5.0<\/td><\/tr>
TabPara[0].Tn<\/td>0.10<\/td>0.10<\/td><\/tr>
TabPara[0].Tv<\/td>0.001<\/td>0.001<\/td><\/tr>
TabPara[0].T1<\/td>0.02<\/td>0.02<\/td><\/tr>
TabPara[0].nRev<\/td>-100.0<\/td>-100.0<\/td><\/tr>
TabPara[0].KpMPC<\/td>1.00<\/td> <\/td><\/tr>
TabPara[0].TnMPC<\/td>0.20<\/td> <\/td><\/tr>
TabPara[0].TvMPC<\/td>0.000<\/td> <\/td><\/tr>
TabPara[0].T1MPC<\/td>0.00<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n
Maximum pressure<\/td>210 bar<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Attention! The following values are the values for the DL650A5 with two KEB motors and drives. If the B&R data is needed, scroll back up.<\/h4>\n\n\n\n

The following values were obtained during tests with two different KEB motors on the DL650A5 located in Austria. Therefore, these are only approximate values intended to give a general idea of how the machine should be set up.<\/p>\n\n\n\n

Pump<\/h3>\n\n\n\n

Servo Pump 1 (KEB 55KW)<\/p>\n\n\n\n

Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Kp<\/td>0.990<\/td>These are the values from past tests for the DLA5 machine with KEB. Check the motor size and which ones are installed<\/td><\/tr>
Tn<\/td>0.010<\/td>These are the values from past tests for the DLA5 machine with KEB. Check the motor size and which ones are installed<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Servo Pumpe 2 (KEB 30KW)<\/p>\n\n\n\n

Parameter<\/td>Value Range<\/td>Description<\/td><\/tr>
Kp<\/td>0.990<\/td>These are the values from past tests for the DLA5 machine with KEB. Check the motor size and which ones are installed<\/td><\/tr>
Tn<\/td>0.010<\/td>These are the values from past tests for the DLA5 machine with KEB. Check the motor size and which ones are installed<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Sevo Pump Parameter<\/h3>\n\n\n\n

Servo Pump Control Mode\/ Basic parameter for servo pump<\/p>\n\n\n\n

Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
Control Mode<\/td>1<\/td>1<\/td><\/tr>
dnUp<\/td>1000.0<\/td>1000.0<\/td><\/tr>
nMax<\/td>3000.0<\/td>3000.0<\/td><\/tr>
Maximum Sensor Pressure<\/td>250<\/td>250<\/td><\/tr>
Voltage at maximum pressure<\/td>10000.0<\/td>10000.0<\/td><\/tr>
Voltage at no pressure<\/td>0.0<\/td>0.0<\/td><\/tr>
Revers<\/td>YES = Green<\/td>YES = Green<\/td><\/tr>
dnDown<\/td>1500.0<\/td>1500.0<\/td><\/tr>
Minimum Pressure<\/td>5.0 bar<\/td> <\/td><\/tr>
Filter pAct<\/td>0.000<\/td> <\/td><\/tr>
Filter pSetDown<\/td>0.000<\/td> <\/td><\/tr>
Filter pSetUp<\/td>0.000<\/td> <\/td><\/tr>
Pressure Sensor Wired<\/td>OFF<\/td>OFF<\/td><\/tr>
Pressure Input<\/td>Drive Input<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n
Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
TabPara[0].Kp<\/td>10.0<\/td>10.0<\/td><\/tr>
TabPara[0].Tn<\/td>0.50<\/td>0.50<\/td><\/tr>
TabPara[0].Tv<\/td>0.025<\/td>0.025<\/td><\/tr>
TabPara[0].T1<\/td>0.02<\/td>0.02<\/td><\/tr>
TabPara[0].nRev<\/td>-100.0<\/td>-100.0<\/td><\/tr>
TabPara[0].KpMPC<\/td>0.10<\/td> <\/td><\/tr>
TabPara[0].TnMPC<\/td>0.00<\/td> <\/td><\/tr>
TabPara[0].TvMPC<\/td>0.000<\/td> <\/td><\/tr>
TabPara[0].T1MPC<\/td>0.00<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Multi parameter of pressure<\/h3>\n\n\n\n
Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
TabPara[0].Kp<\/td>15.0<\/td>15.0<\/td><\/tr>
TabPara[0].Tn<\/td>0.20<\/td>0.20<\/td><\/tr>
TabPara[0].Tv<\/td>0.025<\/td>0.025<\/td><\/tr>
TabPara[0].T1<\/td>0.02<\/td>0.02<\/td><\/tr>
TabPara[0].nRev<\/td>-100.0<\/td>-100.0<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Small Parameter of Pressure<\/h3>\n\n\n\n
Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
TabPara[0].Kp<\/td>15.0<\/td>15.0<\/td><\/tr>
TabPara[0].Tn<\/td>0.20<\/td>0.20<\/td><\/tr>
TabPara[0].Tv<\/td>0.025<\/td>0.025<\/td><\/tr>
TabPara[0].T1<\/td>0.02<\/td>0.02<\/td><\/tr>
TabPara[0].nRev<\/td>-500.0<\/td>-500.0<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Clamp Parameter of Pressure<\/h3>\n\n\n\n
Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
TabPara[0].Kp<\/td>5.0<\/td>5.0<\/td><\/tr>
TabPara[0].Tn<\/td>0.20<\/td>0.20<\/td><\/tr>
TabPara[0].Tv<\/td>0.025<\/td>0.025<\/td><\/tr>
TabPara[0].T1<\/td>0.02<\/td>0.02<\/td><\/tr>
TabPara[0].nRev<\/td>-100.0<\/td>-100.0<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Injection Parameter of Pressure<\/h3>\n\n\n\n
Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
TabPara[0].Kp<\/td>12.0<\/td>12.0<\/td><\/tr>
TabPara[0].Tn<\/td>0.18<\/td>0.18<\/td><\/tr>
TabPara[0].Tv<\/td>0.025<\/td>0.025<\/td><\/tr>
TabPara[0].T1<\/td>0.02<\/td>0.02<\/td><\/tr>
TabPara[0].nRev<\/td>-100.0<\/td>-100.0<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Holdon Parameter of Pressure<\/h3>\n\n\n\n
Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
TabPara[0].Kp<\/td>10.0<\/td>10.0<\/td><\/tr>
TabPara[0].Tn<\/td>0.20<\/td>0.20<\/td><\/tr>
TabPara[0].Tv<\/td>0.025<\/td>0.025<\/td><\/tr>
TabPara[0].T1<\/td>0.02<\/td>0.02<\/td><\/tr>
TabPara[0].nRev<\/td>-100.0<\/td>-100.0<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Ejector Parameter of Pressure<\/h3>\n\n\n\n
Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
TabPara[0].Kp<\/td>10.0<\/td>10.0<\/td><\/tr>
TabPara[0].Tn<\/td>0.20<\/td>0.20<\/td><\/tr>
TabPara[0].Tv<\/td>0.025<\/td>0.025<\/td><\/tr>
TabPara[0].T1<\/td>0.02<\/td>0.02<\/td><\/tr>
TabPara[0].nRev<\/td>-100.0<\/td>-100.0<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Tonnage Parameter of Pressure<\/h3>\n\n\n\n
Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
TabPara[0].Kp<\/td>20.0<\/td>20.0<\/td><\/tr>
TabPara[0].Tn<\/td>0.15<\/td>0.15<\/td><\/tr>
TabPara[0].Tv<\/td>0.025<\/td>0.025<\/td><\/tr>
TabPara[0].T1<\/td>0.02<\/td>0.02<\/td><\/tr>
TabPara[0].nRev<\/td>-400.0<\/td>-400.0<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Half Nut Parameter of Pressure<\/h3>\n\n\n\n
Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
TabPara[0].Kp<\/td>10.0<\/td>10.0<\/td><\/tr>
TabPara[0].Tn<\/td>0.20<\/td>0.20<\/td><\/tr>
TabPara[0].Tv<\/td>0.025<\/td>0.025<\/td><\/tr>
TabPara[0].T1<\/td>0.02<\/td>0.02<\/td><\/tr>
TabPara[0].nRev<\/td>-100.0<\/td>-100.0<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n

Standstill parameter of pressure<\/h3>\n\n\n\n
Parameter<\/td>Value Range (Pump 1)<\/td>Value Range (Pump 2)<\/td><\/tr>
TabPara[0].Kp<\/td>5.0<\/td>5.0<\/td><\/tr>
TabPara[0].Tn<\/td>0.10<\/td>0.10<\/td><\/tr>
TabPara[0].Tv<\/td>0.001<\/td>0.001<\/td><\/tr>
TabPara[0].T1<\/td>0.02<\/td>0.02<\/td><\/tr>
TabPara[0].nRev<\/td>-100.0<\/td>-100.0<\/td><\/tr>
TabPara[0].KpMPC<\/td>1.00<\/td> <\/td><\/tr>
TabPara[0].TnMPC<\/td>0.20<\/td> <\/td><\/tr>
TabPara[0].TvMPC<\/td>0.000<\/td> <\/td><\/tr>
TabPara[0].T1MPC<\/td>0.00<\/td> <\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n
Maximum pressure<\/td>210 bar<\/td><\/tr><\/tbody><\/table><\/figure>\n","protected":false},"excerpt":{"rendered":"

Clamp General Parameter Value Range Description Sensor Type SSI   Actuator Type Hydraulic   Minimum Stroke 0.0 mm   Maximum […]<\/p>\n","protected":false},"author":79,"featured_media":0,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","theme-transparent-header-meta":"","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"default","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"var(--ast-global-color-4)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"footnotes":""},"categories":[318,381],"tags":[],"class_list":["post-3645","post","type-post","status-publish","format-standard","hentry","category-imm-a5","category-imm-a5-manual"],"_links":{"self":[{"href":"https:\/\/www.woojin.help\/ko\/wp-json\/wp\/v2\/posts\/3645","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.woojin.help\/ko\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.woojin.help\/ko\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.woojin.help\/ko\/wp-json\/wp\/v2\/users\/79"}],"replies":[{"embeddable":true,"href":"https:\/\/www.woojin.help\/ko\/wp-json\/wp\/v2\/comments?post=3645"}],"version-history":[{"count":6,"href":"https:\/\/www.woojin.help\/ko\/wp-json\/wp\/v2\/posts\/3645\/revisions"}],"predecessor-version":[{"id":3791,"href":"https:\/\/www.woojin.help\/ko\/wp-json\/wp\/v2\/posts\/3645\/revisions\/3791"}],"wp:attachment":[{"href":"https:\/\/www.woojin.help\/ko\/wp-json\/wp\/v2\/media?parent=3645"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.woojin.help\/ko\/wp-json\/wp\/v2\/categories?post=3645"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.woojin.help\/ko\/wp-json\/wp\/v2\/tags?post=3645"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}